FIRE POLY FPCC
FIRE RETARDANT COATING
for
COMPOSITES ● FIBERGLASS ● PLASTIC PIPE
CLASSIFICATION FOR PLASTIC PIPE
INTERNATIONAL MARITIME ORGANIZATION
(MQ) RESOLUTION A 753 (18) ASTM F1173-95
FIRE RETARDANT COATING
TESTING AGENCY
SOUTHWEST RESEARCH INSTITUTE
| TEST | MATERIAL TESTED | RESULTS |
| Fire Endurance and Hydrostatic Evaluation Based on International Maritime Organization Resolution (MQ) Resolution A.753(18); Appendix 2 and ASTM F1173-95 Section A5 Wet Condition Classification of Water Filled Plastic Pipe | Conley epoxy 20, 6-in. FLGXFLG Spool pipe coated with Flame Safe Chemical Corporation's Fire Poly FPCC | Passed |
| FIRE ENDURANCE | PASSED |
| Number of fire retardant coats | 3 |
| Rate per coat (ft2/gal) | 1050 |
FIRE RETARDANT COATING for STYROFOAM ●POLYURETHANE FOAM ● POLYSTYRENE |
| TEST | MATERIAL TESTED | RESULTS |
| NFPA 701 | 3/4" Styrofoam painted with green latex paint and coated with Flame Safe's Fire Poly FPCC 3/4" Styrofoam (white) coated with Flame Safe's Fire Poly FPCC |
Passed
Passed |
FIRE POLY FPCC |
TECHNICAL DATA (Coating for Plastic Pipe) |
|---|
PRODUCT DESCRIPTION: Aqueous Based Resin
| PRODUCT ANALYSIS | ||||
|---|---|---|---|---|
Total Solids |
46% | PH | 2.5 - 2.8 |
|
Weight per gallon |
10.7 lbs | Flash point | Non-Flammable |
|
Specific gravity |
1.33 | Color | Water clear at 78°F. - Slight haze at 50°F. or lower |
|
Volatability |
Non-Volatile | Solvents | Water(Contains no petroleum or derivatives of petroleum) |
|
Anti-Fungus |
excellent Resistance | Bacterial | Good Resistance |
|
Linear shrinkage |
None | Moisture Absorption | Slight |
|
Corrosive |
Mildly | Toxic | None (when dry) |
|
Scrubability |
1000 cycles | Incompatiblilty | Strong oxidizers, alkalis or acids (materials to avoid)
|
|
Toxic |
None, when dry | |||
RECOMMENDED USE: Pressurized plastic, composite piping systems, styrofoam, polyurethane foam, styrene
FLAME SAFE FIRE POLY FPCC Specially formulated for use on plastic pipe
ENVIRONMENTAL REGULATION:
This product complies will U. S. Federal Regulations concerning the use of lead in paint and hydrocarbon emissions.
 |
QUICK REFERENCE FOR APPLYING FIRE POLY FCC |
|---|
| MATERIAL | APPLICATION |
COVERAGE |
Plastic Pipe, PVC pipe, Composite pipe
Styrofoam, Polyurethane foam, styrene |
Be sure surface is clean and dry before treating. Apply with sprayer head held at 8 to 12 inches from surface. Be sure to allow drying between each coat. |
Apply three (3) coats at 1050 sq. ft. per gallon with the final coverage rate of 350 sq. ft. per gallon
Apply three (3) coats at 600 sq. ft. per gallon with the final coverage rate of 200 sq. ft. per gallon |
EXTERIOR / INTERIOR All surfaces to be treated must be clean and dry. Fire Poly FPCC is water based, clear liquid that becomes insoluble when dry. If over-coating is intended, Fire Poly FPCC is an excellent primer for use under or over latex paints. Avoid wasteful runs and dripping. It should be noted that unlike some products, materials treated with Fire Poly FPCC require no special cutting tools or special fasteners. Contact parts of any equipment should be stainless steel or plastic to prevent chemical reaction and breakdown. Storage may be done in polyethylene containers. |
.jpg) |
|---|
 |
 |
CAUTION:
Product must not freeze. It must not be thinned or diluted.
OVERSPRAY:
The overspray will not harm plants or animals. Spills can be flushed with water. A rag wetted with bleach and water mix will clean up spotting.
CLEAN UP PROCEDURE:
Airless Equipment.
1. Run clear water through the system until coating is flushed out. When minor sudsing on surface stops, the system is flushed.
2. Run bleach and water mix (1 part to 4 parts) through system as solvent for cleaning any residue.
3. Repeat Step 1 if any foaming occurs in Step 2.
4. Lubricate system as specified by equipment manufacturer to combat rusting.
If two or more applications are planned in the same day, the sprayer can be kept clean by running water through the system between applications.
Brushes/Rollers.
1. Clean immediately after use.
2. Wash thoroughly with bleach and water mix (1 part to 4 parts).
SAFETY FIRST
Use approved safety devices (ropes, belts, ridge hooks, ladder, etc.) When working on steep or high areas. Take EXTREME CARE not to step on wet treated area. Surface may be slick until dry.
It is good practice to wear respirator or mask and protect hands with rubber gloves when spraying any coating or chemical. When engineered air control is not feasible, use properly maintained and properly fitted NIOSH approved respirator for solvent vapors. A dusk mask does not provide protection against vapors.
If eye contact occurs, flood with water for fifteen (15) minutes and call a physician. KEEP OUT OF REACH OF CHILDREN. DO NOT TAKE INTERNALLY.
HOME | CONTACTS | FIRE RETARDANT WOOD |Fire Poly FPCC MSDS | TESTING